Skip to main content
Academically Reviewed

Based on the work of Boyd Epley, strength coach at the University of Nebraska.

One-Rep Max Calculator

How much could you lift for one repetition?

A hard set of five reps tells you something about the weight you might lift once. A one-repetition maximum, or 1RM, is the heaviest weight you can lift for one complete repetition of a particular exercise.

Enter the weight and repetitions from a completed set below. This calculator uses the Epley equation to estimate your maximum and shows percentages of the result in kilograms and pounds.

Enter your set

Strength programmes often describe a load as a percentage of your one-rep max. If your maximum were 100 kg, for example, 80% would be 80 kg. An estimate from a recent set provides a useful reference when you have not tested a heavy single. The reference belongs to that exercise: a bench press estimate cannot be transferred to a squat, deadlift, or machine exercise.

The calculation uses the Epley equation: estimated 1RM = weight × (1 + repetitions ÷ 30). Entering 80 kg for five repetitions produces an estimate of about 93.3 kg. The equation works in kilograms or pounds because it multiplies the entered weight by a unitless factor.

Turned around, the equation also tells you what weight to expect for a given number of reps. Each extra rep lowers that weight a little less than the one before. The equation describes the typical link between weight and reps; it does not measure your own muscles, speed, or fatigue.

Another widely used equation, published by Matt Brzycki in 1993, is weight × 36 ÷ (37 − repetitions). It gives slightly lower estimates than Epley for sets of two to nine repetitions and the same estimate at ten: for 80 kg lifted five times, Brzycki gives 90 kg and Epley about 93.3 kg. Neither is right for everyone, and the gap between them is a reminder that any estimate from a submaximal set carries an error of a few percent.

LeSuer and colleagues (1997) compared prediction equations for bench press, squat, and deadlift. Accuracy differed between exercises, so one equation cannot be assumed to fit every lift and lifter equally well. This calculator provides an Epley estimate for the completed set and does not assign a strength category or a population percentile.

The number of reps matters because a long set tests endurance more than strength, so this calculator takes one to fifteen full reps and is most exact at ten or fewer. Reynolds, Gordon, and Robergs (2006) tested 70 adults on the bench press and leg press with sets of one, five, ten, and twenty reps, and sets of five predicted the one-rep max best. That was one study of two exercises, so it does not set an accuracy range for every lift.

Use a set you have already done, close to your limit and with good technique. Count only full reps and the whole weight, including the bar and plates on a barbell. If you stopped because the planned set was over while you still had several reps left, the estimate will usually be too low. You do not need to do a new set to failure.

For a single rep, the calculator uses the weight you entered as your result and adds nothing to it. Lifting a weight once shows you could lift that weight that day; only if it was a true all-out effort is it your tested one-rep max. This keeps an easy warm-up single from being counted as a maximum lift.

For a barbell squat or deadlift, enter the bar and all plates. Your body moves during the lift too, but the calculator estimates the most weight you could put on the bar, so it does not add your body weight. Counting body weight would need a different equation, tested separately for each exercise.

The result includes a table of percentages, rounded to one decimal place. They are plain fractions of your estimate and do not allow for the plates you have, how tired you are that day, or what your training plan asks for. To track progress, compare like with like: the same exercise, equipment, range of motion, and technique. A change in any of these can move the estimate even when your strength has not changed.

IDRlabs made this free calculator for general information. It estimates your one-rep max from a set you have done; it cannot tell whether a particular weight is safe for you to try. For a look at body composition, try the Body Fat Calculator.

For the effort side of training, the Heart Rate Zone Calculator turns your age into five exercise heart rate zones.

To estimate how much energy your days use, including training days, try the Calorie Needs Calculator.

References

Frequently Asked Questions

What is a one-rep max?

Your one-rep maximum is the heaviest weight you can lift for one full repetition of a particular exercise. This calculator estimates it from a completed set.

Which formula does this calculator use?

It uses Epley: 1RM = weight × (1 + repetitions ÷ 30). For one repetition, the entered weight is used without extrapolation.

Why can I enter only one to fifteen repetitions?

Longer sets depend more on muscular endurance. The calculator takes sets of up to fifteen full repetitions, and estimates from more than ten are less exact; focusing on shorter sets does not remove uncertainty about predicting a single maximum.

Should I include the bar’s weight?

Yes. For a barbell lift, enter the total weight of the bar and all plates. Keep the same load convention when comparing sets. This calculator does not account for body weight in weighted pull-ups or dips.

Should I add my body weight for squats or deadlifts?

Enter the external load: the bar and all plates. The Epley calculation estimates a barbell maximum from a barbell set. Although body mass contributes to the movement, adding a proportion of it would create a different model that needs separate validation.

Do I need to lift to failure?

Use a set you have already completed near your limit with good technique. The formulas assume the entered reps were close to the most you could complete at that weight. You do not need to perform a new set to failure or attempt a maximum lift.

Can I use the result to compare different exercises?

The estimate applies to the particular lift and equipment used. A squat, bench press, deadlift, and machine exercise each need their own completed-set input. The calculator provides no ranking against other lifters.

One-Rep Max Calculator

Why Use This Test?

1. Free. Estimate your one-rep max from two numbers, with no registration required.

2. Transparent calculation. Your result shows the Epley equation and the weight and repetitions used to calculate it.

3. Kilograms or pounds. Enter either unit and see the result and percentage loads in both.